The Basics of Plumbing Knowledge When Installing a Bathtub

The Basics of Plumbing Knowledge When Installing a Bathtub

Blog Article

Call Today

Just how do you feel on the subject of Installing A Bathtub?

Installing a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move easily; if you have to open a wall surface to remove the old tub as well as place the new bathtub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Make certain you have actually certified yourself for the job and also fit trying it. Instead of employing a service provider to take control of a halfway-completed job, it is far better to consider employing one prior to you begin. Opportunities are you might need an expert plumber to make tube connections.
This write-up will certainly assist you set up a brand-new bathtub in your shower room if you have actually already acquired a brand-new tub and also don't require to change the setup of your previous water system pipelines.
Your tools and also material checklist need to make up the following:

New Bath tub

Hammer

Pipe Wrenches

Prybar

Safety Glasses

Degree

Pliers

Flexible Wrench

Putty Knife

Screwdriver

Cold Blade

Measuring tape

Pipeline Caps

Preparing for the Setup

First of all, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of the two taps making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final setting.

Removing Old Taps

If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome due to the limited gain access to that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been removed, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.

Installing the Tub

Using the two wood boards under its feet, place the bathtub in the called for setting. The wood boards are practical in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the tub until the level reviews level.
To set up taps, fit all-time low of the outermost flexible faucet port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water as well as inspect all joints and also brand-new pipework for leakages and tighten them if required. Fill up the tub and likewise inspect the overflow outlet as well as the normal outlet for leaks.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the bath tub must wait until the bath tub has been made use of a minimum of once as this will certainly resolve it into its final position.

Fitting New Touches

If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and also the sink. Secure the tap in place with the maker given backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap connectors. The previous type needs to be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.

Tiling Around the Bath tub

In the area where the bathroom satisfies the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, resulting in issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to allow for the movement experienced when the tub is in usage. The sealant can crack rather early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly readily available on the market. It is recommended to fit the tiles using water-resistant or water-proof sticky and cement.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Hopefully you enjoyed reading our topic about How to Install a Bathtub. Many thanks for taking time to browse our content. Sharing is good. Helping people is fun. I love reading our article about How to Install a Bathtub Yourself.

Need assistance? Call.

Report this page